• It works open loop or closed loop and as a rescue device if powered by batteries.
• Sizes up to 90 kW.
• Special software for lift applications.
• Automatic calculation of the deceleration space in one floor run.
• Maximum starting current 2 times the rated one.
• It drives both asynchronous and synchronous motors (PMSM).
• It works at 50°C with 16KHz switching frequency without derating.
• Available also for "clean" energy regeneration application without braking resistor.
• Optional 3-phase input inductance to be in conformity to EN12015:2005.

Regenerative kit for inverter. It recovers the braking energy.

• Recovers into the mains the braking energy normally dissipated by the braking resistor, allowing high energy saving.
• Reduces drastically the heating in the machinery room.
• Suitable for any kind of lift regulated by a VVVF.
• The energy recovered into the mains has a low harmonic content in conformity to the EN 12015 standard.
• Very easy to install, only 5 wires to connect.

NOTA : Takedo Energy is not a speed regulator, but it is present in this section because it is appliable only to a lift system equipped with a VVVF.

Modernization kit to apply HYDROVERT drive to existing hydraulic lifts.

• Suitable for any kind of existing hydraulic lift, without change the control panel, the pump unit, the car and shaft cabling.
• Reduces the consumption during run up to 40%.
• Reduces the stand-by consumption.
• High reduction of the oil heating.
• Offers all the advantages of Hydrovert drive.

Modernization kit to apply HYDROVERT drive to existing hydraulic lifts.

• Suitable for any kind of existing hydraulic lift, without change the control panel, the pump unit, the car and shaft cabling.
• Reduces the consumption during run up to 40%.
• Reduces the stand-by consumption.
• High reduction of the oil heating.
• Offers all the advantages of Hydrovert drive.

• Zero peak starting current.
• Limitation of the installed power.
• Special software for hydraulic lifts.
• Not affected by load nor oil temperature.
• Open loop operation with any kind of lift pump and motor.
• Operation upward only or both upward and downward directions.
• Adjustable inspection speed.
• Available in different sizes up to 30 kW (NXL type) and up to 90 kW
  (NXP type).

• It works in open loop and as a rescue device if powered by batteries.
• Sizes up to 22 kW.
• Special software for lift applications.
• Fan cooler controlled by thermostat.
• Maximum starting current 2 times the rated one.
• It drives both asynchronous how synchronous permanent magnets motors.
• It works at 50°C with 16KHz switching frequency without derating.
• Optional 3-phase input inductance to be in conformity to EN12015:2005.

• Complete kit with:
  VVVF drive,braking resistor,brake contactor,shielded cables,
  accessories for wall mounting.
• Sizes from 3 to 11 kW (E-MOD) and from 5,5 to 22kW (E-POW).
• Easy integration to any kind of control panel and motor.
• Maximum stop precision at floor.
• No noise introduced in the motor.
• Supplied by RED-NX it can bring the car to floor in case of black-out.
• EMC certified by Competent Body.
• Optional 3-phase input inductance to be in conformity to EN12015:2005.

OBSOLETE PRODUCT (Replaced by E-MOD)

OBSOLETE PRODUCT (Replaced by E-POW)

• Compact and easy to install even on existing lifts.
• High running comfort.
• Stop precision.

• No vibrations during running.
• Minimum motor heat even for intense use.
• Can be installed on lifts up to 1.0 m/s.

• Can control start and stop or all the running profile.
• High number of possible adjustments.
• High precision and running comfort.
• Can be installed on lifts up to 2.0 m/s.